Logo Allmyblog
Logo Allmyblog
Lien de l'article    


Contacter l'auteur de ce blog

- boards or you can place two pieces

<< Novembre >>

Ajouter gatehinges66 à vos favoris

- Sliding Gate Whee
 boards or you can place two pieces Alerter l'administrateur Recommander à un ami Lien de l'article 

Step 4 � Cut Top and Bottom Ledge A ledge is just a piece of wood that will <a href="http://www.jinnaike.com/products/gate-stopper/">Gate Stopper</a> be running across the width of all the other boards. Also, add up the total widths of

the boards and see if they correspond to the total width you require for the door opening you calculated in Step 1. A rule of thumb is to make sure that you make doors that have a width that doesnt exceed the height. Even virtually

square doors can be too much to handle for the door hinges. Make sure you buy hinges that are long, heavy-duty, metal, strap hinges. The tools and materials required are also given below. Although the ledge barn doors are a rustic

concept, they have evolved into an attractive modern and efficient way to install weatherproof doors on a barn. Cut two ledge pieces of the exact same width and attach them to the top and bottom of the ledge and brace door. Do that by

using a circular saw. Make sure you cut all the virtual places to the exact same length and that each wood board has the exact same width throughout. Step 3 � Rip Wood Boards for Width If your total board width is not equal to the width

you require, you will have to rip some boards.  . There are two ways to go about this. Step 2 � Cut Your Wood Select the type of wood you want to use and place individual pieces on a pair of saw horses. Tools and Materials Needed     *

Saw horses    * Lumber with standard width    * Circular saw    * Galvanized screws    * Screw gun    * Drill Step 1 � Measure the Size of the Door Opening It is fairly simple to measure the size of the <a

href="http://www.jinnaike.com/products/sliding-gate-wheel/">Sliding Gate Wheel</a> door opening you wish to build the ledge and brace doors for. They are usually a pair of doors that open to reveal a larger space. In either case, it is

important to keep in mind that the total width you get should be  inch less than the door width you calculated in Step 1. Use the drill to make holes to attach the hinges and the door latch. Any other type of hinges will not be able to

support the weight of the door.  Step 5 � Attach Hinges and a Door Latch This is the finishing step. Although the building of ledge and brace doors can be a little complicated, following the given step-by-step guide in this article can

help you in building and finishing your own ledge and brace doors.Ledge and brace doors can also be referred to as ledge barn doors. After you have ripped a board, you can place one of the ripped board pieces in the center of the door

boards or you can place two pieces of ripped boards on the side of the door you wish to build. You should attach them using wood screws. The hinges you use are very important. If there are inconsistencies in the width, use a table saw to

set it right.

  Aucun commentaire | Ecrire un nouveau commentaire Posté le 12-10-2017 à 08h04

Fil RSS 2.0
Ajouter  NetVibes
Ajouter  Google
Ajouter  Yahoo
Ajouter  Bloglines
Ajouter  Technorati

Allzic en direct

Liens Commerciaux
L'information à Lyon
Retrouvez toute l'actu lyonnaise 24/24h 7/7j !

L'information à Annecy
Retrouvez toute l'actu d'Annecy 24/24h 7/7j !

L'information à Grenoble
Retrouvez toute l'actu de Grenoble 24/24h 7/7j !

Application Restaurant
Restaurateurs, demandez un devis pour votre application iPhone

Fete des Lumires
Fête des lumières : vente de luminaires, lampes, ampoules, etc.

Votre publicité ici ?
  Blog créé le 12-10-2017 à 08h01 | Mis à jour le 12-10-2017 à 08h04 | Note : Pas de note